Fieldbus-to-Fiber-Converters-ICF-1170I-Series-Moxa-vietnam.jpg

Fieldbus-to-Fiber Converters ICF-1170I Series Moxa vietnam

Xuất sứ: Moxa VietNam

Nhà cung cấp: Moxa VietNam ANS VietNam

Hãng sản xuất: Moxa

Liên hệ tư vấn

Sales ANS

Fieldbus-to-Fiber Converters ICF-1170I Series Moxa vietnam


Features and Benefits

  • Transmits up to 2 km over optical fiber
  • Converts CAN signals to fiber and fiber to CAN signals
  • Baudrate up to 1 Mbps
  • Dual power inputs for redundancy
  • DIP switch for 120 ohm terminal resistance
  • DIP switch for fiber test mode
  • LEDs for Fiber TX, Fiber RX, Power 1, Power 2
  • Wide temperature model available for -40 to 85°C environments
  • Fully compatible with the ISO 11898 standard

 

Introduction

The ICF-1170I series CAN-to-fiber converters are used to convert CAN signals from copper to optical fiber. The converters come with 2 kV optical isolation for the CANbus system and dual power inputs with alarm contact relay to ensure that your CANbus system will remain online.

 

Fiber Test Mode

Fiber Test Mode can be used to test the fiber cable between two ICF-1170I units, and provides a simple way to determine if the fiber cable is transmitting data correctly. When in Fiber Test Mode, the fiber transceiver (TX) will continuously send out a data signal and the “Fiber TX” LED will light up. On the other side of the connection, when the ICF-1170I fiber transceiver (RX) receives the data signal form the TX side, the “Fiber RX” LED will light up.

Dimensions

• CAN Communication
CAN Interface ISO 11898-2, Terminals (CAN_H, CAN_L,CAN_GND)
Protocols CAN 2.0A and 2.0B (ISO 11898-2)
Connector Type 3-pin removable screw terminal x1
Termination Resistor Dip switch selector for 120 Ω terminal resistor
Transfer Rate Up to 1 Mbps
System Delay 150 ns
Isolation Protection 2 kV
Transmission Distance Max 2 km (depends on the data rate and the protocol used) 
Note: The transmission distance is limited by the signal rate, as indicated in the ISO 11898-2 standard.
LED Indicators PWR1, PWR2, Fiber TX, Fiber RX
• Fiber Communication
Connector Type ST (multi-mode) fiber ports
Fiber Cable Requirements
• Physical Characteristics
Housing Metal
Dimensions 30.3 x 70 x 115 mm (1.19 x 2.76 x 4.53 in)
Weight 178 g (0.39 lb)
• Environmental Limits
Operating Temperature Standard Models: 0 to 60°C (32 to 140°F)
Wide Temp. Models: -40 to 85°C (-40 to 185°F)
Storage Temperature -40 to 85°C (-40 to 185°F)
Ambient Relative Humidity 5 to 95% (non-condensing)
• Power Requirements
Input Voltage 12 to 48 VDC dual power for redundant power
Input Current ICF-1170I: 221 mA @ 12 VDC
Alarm Contact: 1 relay output with current-carrying capacity of 1 A @ 24 VDC
Voltage Reversal Protection Protects against V+/V- reversal
Overcurrent Protection 1.1 A (protects against two signals shorted together)
• Standards and Certifications
Safety UL 508
EMC EN 55032/24
EMI CISPR 32, FCC Part 15B Class A
EMS EN 61000-4-2 (ESD): Contact: 8 kV; Air: 15 kV
EN 61000-4-3 (RS): 80 MHz to 1 GHz: 3 V/m
EN 61000-4-4 (EFT): Power: 4 kV; Signal: 2 kV
EN 61000-4-5 (Surge): Power: 2 kV; Signal: 1 kV
EN 61000-4-6 (CS): 150 kHz to 80 MHz: 3 V/m
EN 61000-4-8 (PFMF)
Green Product RoHS, CRoHS, WEEE
Freefall IEC 60068-2-32
• MTBF (mean time between failures)
Time 792,085 hrs
Standard Telcordia (Bellcore), GB
• Warranty
Warranty Period 5 years
Details www.anhnghison.com